0
Owner's of the Yamaha Musical Instrument MG16 16 Channel Mixer gave it a score of 0 out of 5. Here's how the scores stacked up:
Front & Rear Panels
MG16/6FX
20
5 AUX1 and AUX2 Controls
The AUX1 knob controls the signal level that the channel sends
to the AUX1 bus; the AUX2 knob controls the signal level to
the AUX2 bus. These knobs should generally be set close to the
position.
If you are using stereo channels, the signals from the L (odd)
and R (even) channels are mixed and sent to the AUX1 and
AUX2 buses.
These controls allow you to output the signal to the
AUX buses regardless of the setting of the ST
switch
9.
6 PRE Switch
Selects whether the pre-fader or the post-fader signal is fed to
the AUX2 bus. If you set the switch on ( ), the mixer sends
the pre-fader signal—the signal prior to passage though chan-
nel fader
B—to the AUX2 bus, so that AUX2 output is not
affected by the fader. If you set the switch off ( ) the mixer
sends the post-fader signal to the AUX2 bus.
Note that this switch applies to AUX2 only. The signal to the
AUX1 bus always passes through the channel fader first.
7 EFFECT Control
Adjusts the level of the signal sent from the channel to the
EFFECT bus. Note that the signal level will also vary accord-
ing to the setting of the channel fader.
If you are using stereo channels (CHs 9/10, 11/12, 13/14,
15/16), the signals from the L (odd) and R (even) channels are
mixed and then sent to the EFFECT bus.
8 PAN Control (CHs 1 to 8)
PAN/BAL Control (9/10 and 11/12)
BAL Control (13/14 and 15/16)
The PAN control determines the positioning of the channel’s
signal on the Group 1-2/3-4 buses or on the Stereo L and R
buses.
The BAL control knob sets the balance between left and right
channels. Signals into to the L input (odd channel) feed to the
Group 1/3 bus or to the Stereo L bus; signals into the R input
(even channel) feed to the Group 2/4 bus or the Stereo R bus.
On channels where this knob provides both PAN
and BAL controls (9/10 and 11/12), the knob oper-
ates as a PAN control if you are inputting through
the MIC jack or into the L (MONO) input only, and
operates as a BAL control if you are inputting into
both L and R inputs.
9 ST Switch
This switch assigns the channel’s signal to the Stereo L and R
buses. To send the signal to the Stereo bus, set the switch on by
pressing it in ( ). The switch lights up orange to indicate that
it is on.
0 PFL (Pre-Fader Listen) Switch
This switch lets you monitor the channel’s pre-fader signal. To
set the switch on, press it in ( ) so that it lights up. When the
switch is on, the mixer outputs the channel’s pre-fader signal to
the PHONES and C-R OUT jacks, for monitoring.
A GROUP Switches
Use these switches to send the channel's signal to the Group
1-2 and/or Group 3-4 buses. Setting the switch on ( ) causes
the signal to be sent to the corresponding group buses.
These switches allow you to assign the signal to
either or both groups regardless of the setting of the
ST switch 9.
B Channel Fader
Adjusts the output level of the signal being input to the chan-
nel. Use these faders to adjust the volume balance among the
various channels.
To reduce noise, set the fader sliders for unused
channels all the way down.
NOTE
NOTE
NOTE
NOTE
MG16-6FX.book Page 20 Saturday, January 25, 2003 10:13 AM
Find Your Products By Category
Please Login
