Casio Electronic Keyboard Keyboard User Manual

0

Out of 0 Ratings

Owner's of the Casio Electronic Keyboard Keyboard gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 169
 
Using the Tone Editor
E-48
The table below shows the parameters that can be configured on the tone editor screen. For information about each parameter,
also refer to “Tone Creation Overview” (page E-44).
The settings marked with an asterisk (*) in the “Setting Range” column are initial defaults.
Tone Parameter Settings
Parameter Name Description Setting Range
AttackTime
(Attack Time)
Specifies the time until a note starts to sound after a key is pressed. –64 to 0
*
to +63
ReleasTime
(Release Time)
Specifies the time a note continues to sound after a key is released. –64 to 0
*
to +63
CutOff
(Cutoff Frequency)
Adjusts timbre by attenuating note components that are higher than a certain
frequency. A larger value produces a brighter, harder sound, while a lower
value produces a mellower, softer sound.
–64 to 0
*
to +63
Vib.Type
(Vibrato Type)
Specifies the vibrato type (vibrato waveform). Sin
*
, Tri, Saw, Sqr
Vib.Depth
(Vibrato Depth)
Specifies how much vibrato is applied to a note. –64 to 0
*
to +63
Vib.Rate
(Vibrato Rate)
Specifies the speed of the vibrato applied to a note. –64 to 0
*
to +63
Vib.Delay
(Vibrato Delay)
Specifies how much time elapses until vibrato starts. –64 to 0
*
to +63
Oct.Shift
(Octave Shift)
Shifts the pitch upwards or downwards in octave steps. –2 to 0
*
to +2
Volume
(Volume)
Specifies the volume level of all tones. A larger value sets a higher volume
level.
0 to 127
*
TouchSense
(Touch Sense)
Specifies how much the volume changes in accordance with the relative
amount of pressure applied to keyboard keys. A larger positive value results
more change in volume in accordance with key pressure. A larger negative
values results in less change in volume in accordance with key pressure. Key
pressure does not affect volume when a value of 0 is set.
–64 to 0 to +63
*
Rev.Send
(Reverb Send)
Specifies how much reverb is applied for each tone. 0 to 40
*
to 127
Cho.Send
(Chorus Send)
Specifies how much chorus is applied for each tone. 0
*
to 127
DSP On Off
(DSP On/Off)
Specifies whether DSP should be applied (on) or not applied (oFF) to notes.
The following four settings become enabled when “on” is selected for this
setting.
oFF
*
, on
DSP Specifies the DSP to be applied to tones using DSP numbers (001 to 100:
Preset DSPs; 101 to 200: User DSPs). Selecting “ton” applies the initial preset
DSP of each tone.
ton
*
, 001 to 200
DSP Type
(DSP Type)
Shows the DSP type number corresponding to the above DSP value that is set
automatically as the initial default setting.
*1
You can modify the initial default
setting and select a different DSP type.
01 to 46
*1
Setting Description Waveform
Sin Sine wave
Tri Triangle wave
Saw Sawtooth wave
Sqr Square wave

   Find Your Products By Category